Home > Cannot Boot > Cannot Boot Dvd Sata Drive

Cannot Boot Dvd Sata Drive

Arrgh, well I enabled AHCI and then looked to incrase the timeout value, but it was already set to the maximum (35 secs). I have two SATA connectors on the motherboard, so the SATA drive is plugged directly into that. –Kevin Sep 11 '12 at 14:07 With SATA you do not have I know the function keys used to work in the BIOS setup but they don't any more. I have no f*ckin' idea. this contact form

But thanks anyway. You ever ran a system with an add-in RAID card? When I go into the Device Manager, it sees the DVD/CD drive OK, but there is no other installed device that would equate to what I see as F: in File Then I went into BIOS and set the boot priority to go CDROM, then HDD. http://www.tomshardware.com/forum/250291-32-booting-sata-drive

Press F6 for "Other Options." Try to apply boot parameters: BootParameters Other Installation Options If unfortunately none of these options worked for you, there are still other options. The IDE hard drive shows up as Ch 0 Master and the DVD shows up as Ch 1 Master. Sam, thanks for the kind words.

You now have a good chance of booting Ubuntu. Thanks for reading hope this helps Patrick Patricks A+ PC Repairs share|improve this answer answered Feb 7 '13 at 0:04 Patrick 1 add a comment| up vote 0 down vote If The Blue end connector is attached to the motherboard IDE header, the Gray middle connector is attached to the CD/ROM drive, and the Black end connector is attached to the hard Did you update the motherboard to the latest BIOS version?

I set the priority to CDROM first, then hard disk. If you look at the manual, page 71 section 3.1, there are several ways to update the BIOS. The PC is an older (~8 years) Dell Inspiron. http://www.sevenforums.com/hardware-devices/168368-sata-dvd-not-bootable-bios.html I suspect a keyboard manufacturer has planted it to increase business due to cheapskates *ahem* who don't replace their keyboards as often as the industry would like... · actions · 2009-Oct-5

And what happened to E: ?? My system is configured as you have shown with the DVD connected to SATA2_0 and all the defaults (i.e., SATA ports in native IDE mode). Reports: · Posted 7 years ago Top SamDenst Posts: 10 This post has been reported. The DVD was not burned properly Check and make sure that the disk was burned properly.

Then after I did all of that I thought I'd install the other 2 drives. There is a secondary storage controller, the Marvell, which handles the IDE (PATA) ports and the eSATA ports. I would cycle through the "Boot Order" selecting the first boot device as CD/ROM, the second boot device as CD/ROM, and the third boot device as HDD-0. I'm assuming it's an internal drive.

I'm really sorry for asking this, but you're blowing my mind. weblink I have the Knack. ** If I haven't replied in 48 hours, please send me a message. LCD/CRT Model: Eyefinity - 3x Dell U3011 Case: CaseLabs TH10 Sound Card: Creative X-Fi Titanium HD Power Supply: Corsair AX1200W + AX850W Software: Windows 7 x64 Thanks Mussels, completely forgot about To learn more and to read the lawsuit, click here.

And I should have thought of that because I have the same issue with my old Adaptec AHA-2940W SCSI controller. TURN OFF RAID in the BIOS.8) Leave the SATA DVD/RW drive disconnected entirely from the system until you have both the HDD and the CD/ROM working on IDE channel-0, device-0 and I have two SATA connectors on the motherboard, so the remaining healthy SATA data drive (a Samsung 500Gb) is plugged into SATA1. (In the BIOS settings it shows up as IDE navigate here Please use your experience in overcoming the roadblocks it has put in your way to make this wiki as accurate as possible.

Click to expand... The DVD shows up in the BIOS as IDE master 2 with master 1 being blank. EG, my board has 6 intel (bootable) and 2 JMICRON (not bootable) Jmatt110 says thanks.

Win98 lives -- now in your browser! [Microsoft] by aurgathor179.

Reports: · Posted 7 years ago Top Hermitt Posts: 1310 This post has been reported. Reports: · Posted 7 years ago Top Topic Closed This topic has been closed to new replies. It's also a good idea with a new build to load it up with all the parts and do some stress testing. I just have to say that.

My two IDE hard drives (the "new" Western Digital 80Gb with XP on it and a Western Digital 250Gb with no OS) are now on one channel. If you choose [Auto], the BIOS determines the type of device, and its characteristics. [Auto] is the preferred setting. What now? his comment is here Tank-Fighting Alien Why does Friedberg say that the role of the determinant is less central than in former times?

If the operating system/installer fails to find/boot from the whichever optical drive has the media in it, it will fail-over to the next device that is bootable; the HDD, Floppy, USB, Further investigation shows some confusing data that I don't know how to resolve. On other systems it could be a different key, or combination of keys like ESC, F1, F2, F10, F12, Ctrl-Esc, Alt-Esc, Ctrl-Alt-Esc, Ctrl-Alt-Enter, Ins or even others. Can't boot from DVD drive Discussion in 'Motherboards & Memory' started by Jmatt110, Aug 26, 2009.