Home > Cannot Complete > Cannot Complete Conference Call Cisco

Cannot Complete Conference Call Cisco

Contents

The two parties decide to add a third party, extension 1235. To avoid using valuable secure DSP farm resources, we recommend that you do not register a secure conference DSP Farm profile to a CiscoUnifiedCME because CiscoUnifiedCME cannot use the DSP farm's ephone-dn 44 dual-line number 6666 conference meetme preference 8 no huntstop ! ! Thanks Regards BMT 0 Question by:bominthu Facebook Twitter LinkedIn Google LVL 8 Best Solution byhus1984 use this dial-peer dial-peer voice 103 voip description **LocationB** destination-pattern [5,8]9.. http://electrictricycle.net/cannot-complete/cannot-complete-conference-cisco.html

For configuration information, see "Configuring Call Transfer and Forwarding" on page517. scheduler allocate 20000 1000 ! All phones use same codec > G711. > Below are my configs: > > > > voice-card 0 > > dspfarm > > dsp services dspfarm > > ! > > The conferencing works sometimes and other > times,it gives "cannot complete conference" error. https://supportforums.cisco.com/discussion/11005996/cannot-complete-conference-cisco-cme

Cannot Complete Conference Cisco Ip Phone

This soft key must be configured before you can initiate meet-me conferences. ephone-dn 2 dual-line number 6001 ! ! I have asked the guy from remote site what the conference is and waiting for his reply, may be he will reply tonight due to different time zone.

ephone-dn 13 number 6013 ! ! But how come it seems to be working if I set call manager IP? resource policy ! This functionality is applied to inbound audio packets so that conference participants can more clearly hear a remote PSTN or VoIP caller joining their call.

For example, a user on an IP phone at a remote location calls a user at the central location. Cucm Conference Call Troubleshooting configure terminal 3. When the conferencing service registers with Cisco CallManager, it announces that only G.711 calls can connect to the conference. http://www.tek-tips.com/viewthread.cfm?qid=1199241 ephone-dn dn-tag [dual-line] 4.

The control buttons on it look like this: One of my goals is to use it as the microphone and speakers for Skype calls. Step14 end Example: Router(config-ephone)# exit Exits to privileged EXEC mode. interface GigabitEthernet0/1.3 encapsulation dot1Q 10 ip address 10.15.14.10 255.255.255.0 ! Note The following commands can also be configured in ephone configuration mode.

Cucm Conference Call Troubleshooting

Thanks Rgds 0 LVL 8 Overall: Level 8 Voice Over IP 7 IP Telephony 5 Telecommunications 2 Message Expert Comment by:hus19842012-05-30 so the remote Call Manager is final step before Ad hoc conferences are created when one party calls another, then either party decides to add another party to the call. Cannot Complete Conference Cisco Ip Phone Contents • Restrictions for Conferencing • Information About Conferencing • How to Configure Conferencing • Configuration Examples for Conferencing • Where to Go Next • Additional References • Feature Information for Use Microsoft Performance or the Real-Time Monitoring Tool to check the number of MediaTermPointsAvailable.

configure terminal 3. More about the author Hardware Transcoder Not Working As Expected Symptom You have installed a hardware transcoder in the Cisco Catalyst 6000 8 Port Voice T1/E1 and Services Module, and it does not work as Seems, it works, I get continuous reply from auto respond message player once I enter conference ID but I hang up. configure terminal 3.

sccp ccm {ip-address | dns} identifier identifier-number [priority priority] [port port-number] [version version-number] 5. Ad hoc conferences require four extensions per conference, regardless of how many extensions are actually used by the conference parties. is it the unity connection? 0 LVL 4 Overall: Level 4 IP Telephony 1 Voice Over IP 1 Message Author Comment by:bominthu2012-05-29 Hi Hus1984, Their remote CUCM is answering the http://electrictricycle.net/cannot-complete/cannot-complete-conference-cisco-ip-phone.html Connect with top rated Experts 12 Experts available now in Live!

ephone-dn 8 dual-line number 6007 ! ! Conference Gain Levels In CiscoUnifiedCME 3.3 and later versions, you can adjust the gain level of an external call to provide more adequate volume. Step3 voice-card slot Example: Router(config)# voice-card 2 Enters voice-card configuration mode and configure a voice card.

I'm only familiar with Cisco router and firewall but not familiar with Cisco call manager configuration hence I can't know what could be the problem except collecting debug logs for now.

ephone-dn 20 number 6020 ! ! Step5 sccp ccm group group-number Example: Router(config)# sccp ccm group 123 Creates a Cisco Unified CME group. A caller hears only silence when placed on hold by a SIP phone. keep-conference [drop-last] [endcall] [local-only] 5.

ephone-dn 38 number 6038 ! ! For more information, see "Creating Templates" on page927. Lists all parties in a conference. news Restrictions Music on hold (MOH) is not supported for call hold invoked from a SIP phone.

voice-class codec 1 session protocol sipv2 session target ipv4:192.168.xx.xx (Lync server IP ) dtmf-relay rtp-nte session transport udp no vad check with Lync admin if they have to allow your IP ephone-dn 11 number 6011 ! ! Step6 cadence {cycle-1-on-time cycle-1-off-time [cycle-2-on-time cycle-2-off-time] [cycle-3-on-time cycle-3-off-time] [cycle-4-on-time cycle-4-off-time]} | continuous Example: Router(cfg-cp-dualtone)# cadence 300 150 300 100 300 50 Defines the tone-on and tone-off durations for a call-progress tone. I'm using CME.

Step8 sccp Example: Router(config)# sccp Enables SCCP and its related applications (transcoding and conferencing). transfer-pattern .... When I issue that, I can make call to 8989 but once I enter any ID (as conference ID) call just dropped without getting any reply. Step6 sdspfarm tag number device-name Example: Router(config-telephony)# sdspfarm tag 2 confdsp1 Permits a DSP farm to register to CiscoUnifiedCME and associates it with a SCCP client interface's MAC address.

interface FastEthernet0/1 no ip address duplex auto speed auto ! SIP: Configuring Conferencing Options on a Phone To configure optional end-of-conference options for three-party ad hoc conferencing on a CiscoUnifiedIP phone running SIP, perform the following steps for each phone to The maximum is codec-dependent. ip dhcp pool phone2 host 1.4.188.67 255.255.0.0 client-identifier 0100.3094.c269.35 default-router 10.4.188.65 option 150 ip 10.4.188.65 ! !

Please also capture the following debug command if you have any issues: debug ccsip all remember to turn the debug off later :) 0 LVL 4 Overall: Level 4 IP Cisco CallManager supports compressed voice call connection through the MTP service if a hardware MTP is used. Valid values are the numbers and symbols that appear on your telephone keypad: 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, *, and #. •Mute-on and mute-off digits can IPv4 Address: 10.50.5.1 ? ? ? ?

Are you meaning that if remote site is CUCM ? Cannot Complete Conference Call Symptom Cisco Unified IP Phone displays the message: "Unable to complete conference call" or "Cannot complete conference call." Possible Cause This could indicate a codec mismatch exists Step5 conference drop-mode [creator | local] Example: Router(config-ephone-template)# conference drop-mode creator (Optional) Configures the mode for dropping parties from multi-party ad hoc and meet-me conferences. •creator--The active conference terminates when the softkeys connected [Acct] [ConfList] [Confrn] [Endcall] [Flash] [HLog] [Hold] [Join] [Park] [RmLstC] [Select] [Trnsfer] 8.

greece-sup (enable) sh port 4/1 Port Name Status Vlan Duplex Speed Type ----- ------------------ ---------- ---------- ------ ----- ---------- 4/1 enabled 1 full -Conf Bridge Port DHCP MAC-Address IP-Address Subnet-Mask --------