Home > Cannot Complete > Cannot Complete Conference Call

Cannot Complete Conference Call


Router# show running-config ! A moderately complex configuration may exceed the default 256 MB DRAM and require 512 MB DRAM. Prerequisites •To facilitate call transfer by using the Confrn softkey, conference and transfer attended or transfer blind must be enabled. The same will be the case if initiator hangs up local-only: When the initiator disconnects, parties will remain connected (using transfer) only if one of them is local to CME For http://electrictricycle.net/cannot-complete/cannot-complete-conference-call-cisco.html

end DSP Farm and Cisco Unified CME on Different Routers: Example In this example, the DSP farm and Cisco Unified CME are on different routers as shown in Figure44. Note Configuring multi-party ad hoc conferencing in CiscoUnifiedCME disables three-party ad hoc conferencing. resource policy ! Step4 conference add-mode [creator] Example: Router(config-ephone-template)# conference add-mode creator (Optional) Configures the mode for adding parties to conferences. •creator--Only the creator can add parties to the conference. my response

Cannot Complete Conference Cisco Ip Phone

voice-card 1 no dspfarm dsp services dspfarm
interface GigabitEthernet0/0 ip address duplex auto speed auto ! ephone-dn 20 octo-line number 3020 description **** HW CFB *** conference ad-hoc SiteC#show call leg active summary G L Elog A/O FAX T Codec type Peer Address IP R: G17B4 L Figure41 Simple Ad Hoc Conference Using the Conf Soft Key You can configure ad hoc conferencing so that only the creator can add parties to the conference.

Enable adding parties to conference. CME won't select idle channels from other DNs within the same phone similar to single/dual lines behavior. - CME admin can assign admin role to any of the ephones within Seems the command "dtmf-relay cisco-rtp " is the cause But not sure yet until I setup the conference meeting with remote guy Thanks a lot Hus ..really. boot-start-marker boot-end-marker ! !

Figure 25-1 Multisite WAN Using Centralized MTP Transcoding and Conferencing Services IP-to-IP Packet Transcoding Across Intercluster Trunks Intercluster trunks connect Cisco CallManager clusters. Cucm Conference Call Troubleshooting Step2 configure terminal Example: Router# configure terminal Enters global configuration mode. Note Table36 lists the CiscoUnifiedCME version that introduced support for a given feature. By joining you are opting in to receive e-mail.

if your anything like me you have had a bit of difficulty with the new NAT statements in the ASA 8.3 and above firmware, I hav... ephone-dn 35 number 6035 ! ! ephone 1 ephone-template 1 mac-address C863.B965.2401 type anl button 1:1 ! ! ! Click Here to join Tek-Tips and talk with other members!

Cucm Conference Call Troubleshooting

telephony-service 4. http://www.gossamer-threads.com/lists/cisco/voip/112480 ephone phone-tag 13. Cannot Complete Conference Cisco Ip Phone When the conferencing service registers with Cisco CallManager, it announces that only G.711 calls can connect to the conference. dualtone conference 5.

Note The template-tag must be the same as the template-tag in Step 3. More about the author How can I make MTP resource available ? Step2 configure terminal Example: Router# configure terminal Enters global configuration mode. configure terminal 3.

end DETAILED STEPS Command or Action Purpose Step1 enable Example: Router> enable Enables privileged EXEC mode. •Enter your password if prompted. thnxReplyDeleteDale HollowayMarch 27, 2014 at 11:00 AMHave you ever seen software conference not work on CME out of the box? Press Update to update the list of parties in the conference, for instance, to verify that a party has been removed from the conference. •Join--Joins an established call to conference. check my blog My CME config file is attached in my first comment if you need.

In case XCODER isn't available, conference can't be completed. - The max number of software ad-hoc simultaneous conferences depends on CME platform. - Each phone can be part of one However, SIP phones can be parties of hardware conference (SCCP phone will be initiator). - Each phone can be part of one conference at a time - For CFB to No server config necessary.

Finding Feature Information in This Module Your CiscoUnifiedCME version may not support all of the features documented in this module.

For a list of the versions in which each feature is supported, see the "Feature Information for Conferencing" section. conference-leave custom-cptone cptone-name 7. ephone-dn 67 dual-line number 8889 name Conference conference ad-hoc preference 3 ! ! Step7 no huntstop [channel] Example: Router(config-ephone-dn)# no huntstop Continues call hunting behavior for an extension (ephone-dn) or an extension channel. •Remember to configure no huntstop for all DNs except the last

Step4 sccp ccm {ip-address | dns} identifier identifier-number [priority priority] [port port-number] [version version-number] Example: Router(config)# sccp ccm identifier 100 version 4.0 Adds a Cisco Unified CME router to the For example,ephone-dn  179  dual-line number A000 description ad-hoc conference ad-hoc no huntstop See More 1 2 3 4 5 Overall Rating: 5 (1 ratings) Log in or register to post comments ephone-dn 29 dual-line number 8888 conference meetme preference 1 no huntstop ! ! news ephone-dn 53 dual-line number A0001 name conference conference ad-hoc preference 3 no huntstop ! !

ephone 1 mac-address 011F.92A0.C10B type 7960 addon 1 7914 no dnd feature-ring keep-conference Troubleshooting Three-Party Ad Hoc Conferencing Step1 Use the debug ephone commands to observe messages and states associated with Are you aComputer / IT professional?Join Tek-Tips Forums! voice-card 3 dspfarm ! Table36 Feature Information for Conferencing Feature Name CiscoUnifiedCMEVersion Feature Information Meet-me Conferences 4.1 Added support for hardware-based meet-me conferences created by parties calling a designated conference number.

Registration on or use of this site constitutes acceptance of our Privacy Policy.